Stokes Disc Diffusion method: Principle, Procedure and Interpretation of results 5/5 (4)

Stokes Disc Diffusion Technique varies from Kirby Bauer disc diffusion in the use of both control and test strain on a same plate. Stokes disc diffusion technique is not as highly standardized as the Kirby-Bauer technique and is used in laboratories particularly when the exact amount of antimicrobial in a disc cannot be guaranteed due to difficulties in obtaining discs and storing them correctly or when the other conditions required for the Kirby-Bauer technique cannot be met.

Comparative disc diffusion techniques based on Stokes method is still in wide use in majority of laboratories in UK,  to determine antibiotic susceptibility. The stokes’ method allows each individual isolate to be compared with a sensitive control  of the same or similar species which is subjected to the same technical conditions of medium, incubation time, atmosphere, temperature and disc content.  As control and test organisms are adjacent on the same plate the difference between respective zone sizes can be measured directly.

Inoculum Preparation

The growth method is performed as follows

  1. At least three to five well-isolated colonies of the same morphological type of both test and control strains are selected from an agar plate culture. The top of each colony is touched with a loop, and the growth is transferred into a tube containing 4 to 5 ml of a suitable broth medium, such as tryptic soy broth.
  2. The broth culture is incubated at 37°C until it achieves or exceeds the turbidity of the 0.5 McFarland standard (usually 2 to 6 hours)
  3. The turbidity of the actively growing broth culture is adjusted with sterile saline or broth to obtain a turbidity optically comparable to that of the 0.5 McFarland standard. This results in a suspension containing approximately 1 to 2 x 108 CFU/ml for E.coli ATCC 25922.  To perform this step properly, either a photometric device can be used or, if done visually, adequate light is needed to visually compare the inoculum tube and the 0.5 McFarland standard against a card with a white background and contrasting black lines.
  4. Optimally, within 15 minutes after adjusting the turbidity of the inoculum and control strains suspension, sterile cotton swabs are  dipped into each of the adjusted suspension.  The swabs should be rotated several times and pressed firmly on the inside wall of the tube above the fluid level.  This will remove excess inoculum from the swab.
  5. A dried Müeller-Hinton agar plate is divided into 3 halves.
  6. The dried surface of a Müeller-Hinton agar plate is inoculated by streaking the control strains evenly across the upper and lower thirds of the plate,and the test strains between the control ,leaving a distance of not more than 5mm on each side of the control strain.
  7. Allow the inocula to dry for few minutes with the lid.
  8. Place antimicrobial discs in the gap between the test and control strain using a sterile forcep and press gently.
  9. Within 30 mins of applying the discs, incubate the plates aerobically at 35-37 0C for 18-24 hrs.

Inoculation of Test Plates

NOTE: Extremes in inoculum density must be avoided.  Never use undiluted overnight broth cultures or other unstandardized inocula for streaking plates.

Interpretation of results

Measure the radius of the inhibition zone from the edge of the disc to the edge of the zone.

Sensitive (S): Zone radius is wider than or equal to,or not more than 3mm smaller than the control.

Intermediate (I): Zone Radius is > 2 mm but smaller than the control by > 3mm.

Resistant (R): No zone of inhibition or zone radius measures 2mm or less


Advantages of Stokes method:

  1. The control strain and test strain can be checked on the same plate.
  2. More reliable for the quality testing of discs.
  3. The effect of variation of environmental condition like temperature, time affect both simultaneously thus minimizing error
  4. Errors due to using too heavy or light inoculums will be detected.

Please rate this


4 thoughts on “Stokes Disc Diffusion method: Principle, Procedure and Interpretation of results

Leave a Reply to anwarsaleem Cancel reply